The Surfing Handbook only recommends products we like and use, period. Sometimes we get an affiliate comission from links, but this helps us keep the site running!

Surfing 101

Surfboard Traction Pad Guide – Placement And More

Surfboard Traction Pads / Deck Grips / Tailpads

Surfboard traction pads, deck grips, tailpads. There are several names for this piece of grippy foam that most shortboards and a few longboards have on the end of the deck.

Put simply, traction pads give your rear foot a bit more grip on the board, allowing you to pull harder maneuvers without having to worry about whether or not your wax is sticky or bumpy enough. Some surfboard traction pads have ridges at the back that allow your foot even more control over the board for harder snaps and aerial maneuvers.

There are several brands of surfboard traction pads on the market, and it’s tough to go wrong since traction pads are a relatively simple piece of equipment.

I personally recommend DaKine tail pads, however Gorilla Grip and OAM produce good tail pads as well.

Color: This is up to you. One word of advice, however, don’t get a white traction pad. The guy at the shop said it wouldn’t get dirty, but it did. He was probably trying to get rid of it! Now it looks a little trashed, but it still works fine.

How To Apply A Surfboard Traction Pad & Surfboard Traction Pad Placement

Applying a tail pad to your pristine surfboard can be a little nerve-wracking, but there is a very simple way to do it.

FIRST: Make sure there is NO wax on your board. If it’s brand new, take a cloth and wipe away any fiberglass dust that might be on the board from production. If you’ve had wax on it, leave it in the sun for a few minutes to soften the wax, or pour hot water on it. Then scrape away the wax from the area with a wax comb or other soft plastic edge (your old credit cards work well) and finish with a wax remover. If it’s winter, you can take a hairblower on a LOW setting and blow the wax until it is soft enough to remove. Make sure that you wipe away all the wax remover and bits of wax.

  • Cut the plastic around the edge of the tailpad and remove the cardboard backing—but leave the pad itself in the plastic so it stays together.
  • Put the tail pad on the board (still in the plastic) and figure out where you want it to go. Some surfers like to have the rear kick-up ridge positioned either directly over the front of the centermost fin, others like to have it right in front of the leash plug. If this is your first traction pad, a safe bet is to put the rear ridge over the center of the middle rear fin.
  • Mark off the position of the pad with a pencil. Use the stringer to make sure you’ve got your pad centered.
  • Peel off the adhesive paper on the pad, being careful not to let the glue stick to anything.
  • Take the entire pad and carefully place it onto the area marked with your pencil.
  • Press down firmly for about 20-30 seconds to bond the adhesive.
  • Carefully peel away the plastic packaging.
  • It’s advised to wait a day to use the board, but I’ve heard of people going in the water right away. It’s up to you, but I’d recommend waiting at least 12 hours.

That wasn’t so hard now, was it? Some people like to spread the pieces of their traction pad around wider or tighter than the factory “preset.” If you want to do this, just take a pencil and trace the different pieces individually. You can use a little piece of double stick tape so they don’t move around as you arrange them.

Removing a Surfboard Traction Pad

This is difficult, and is easier on epoxy boards than fiberglass boards. If you want to remove a tail pad from a fiberglass board you run the risk of delaminating the board, pulling the fiberglass away from the foam. This could ruin your board, so it’s not recommended.

If you MUST remove the pad, do it very, very slowly and carefully, a little at a time. If you’re going to put a new pad on, don’t worry about a little sticky adhesive left over. If you just want to get rid of the thing completely, a small amount of paint thinner on a rag or paper towel should take care of the adhesive.

Bestsellers According To Amazon

No products found.

Hayley Gordon

Hayley Gordon has been surfing for over 20 years. Riding both shortboards and longboards, she's traveled the world to surf but mainly sticks to her two home locations of San Diego and Long Island.

Related Articles

Subscribe
Notify of
guest

7 Comments
Inline Feedbacks
View all comments
Scott
Scott
5 years ago

By far, I prefer white traction pads,… because they don’t get especially dirty unless you surf in dirty water.
I surf in San Diego,…. and I don’t surf often, but I surf HPSB’s. Black/dark pads just don’t like right.

matthew
9 years ago

wait 24 hours if you can!!!!! usually the leash pulls on my pad , usually tie my laces to longm but!!! pad will stick if you wait!!!! make sure you hold when it bonds! i am super impatient and surf my new boards as soon as the pad is on that is why they eventually will fall off. and i most certainly surf more than you. cuss your vagina probably hurts and they waves ‘arent good enough” . the waves are always good. you aint broke you just broken hearted <3 <3 mIm

Laird
Laird
7 years ago
Reply to  matthew

Ok kook

BO C.
BO C.
12 years ago

use a air dryer and heat the pad a little and make sure your board is at least 72 degrees Fahrenheit. then stick it on and press down all over it and especiallyt the edges.

Maximilian
Maximilian
13 years ago

What can I do if the traction pad does not want to stick to the board? Can I stick it back on or something? If yes, what glue should I use? Thanks
max

Maximilian
Maximilian
13 years ago

Thanks Guys for the infos.
The only problem I have with my traction pad(which came with the board) is that it does not stick too well to the board. What can I do, or with what can I stick it back on again? I have a TrenchTown TT Pro 6.0 if that should matter.

Steve
Steve
15 years ago

Thanks for an informative article. Up until now i have been sitting here looking at my new traction pad and wondering where exactly I should put it lol. Just one question tho before i go ahead and stick it on, does the placement remain the same for longer boards? I have an 8′ minimal.

Back to top button
7
0
Would love your thoughts, please comment.x
()
x